Artikel (52)
Cane cutter blade (blade chopper cane), which is a tool used for chopping cane. This tool acts as a cane crusher, made of low steel carbon. Constraints that occur on Cane Cutter Blade is a high wear rate, thus disrupting the productivity of the industry. The company handles this problem by provi...
Jurnal Ilmiah Teknik Mesin FEMA; Vol. 1 No. 3 (2013) | 2013
Indonesia merupakan negara yang sedang berkembang di bidang industri dan memiliki tingkat pertumbuhan penduduk yang tinggi. Hal ini mengakibatkan tidak terpenuhinya permintaan akan ketersediaan energi listrik. Seperti telah diketahui bahwa pada umumnya bahan bakar dari pembangkit energi listrik ters...
Jurnal Ilmiah Teknik Mesin FEMA; Vol. 1 No. 3 (2013) | 2013
This paper describes aerodynamic tests (wind tunnel test) for a model of secondary cabin roof (SCR) applied in BMW M3 E92 Coupe. SCR is a vehicle accessory installed on vehicle roof useful to block heats from sun while the car parking. The test were conducted at UPT-Laboratorium Aero Gas Dinamika da...
Jurnal Ilmiah Teknik Mesin FEMA; Vol. 1 No. 3 (2013) | 2013
The aim of this research is to know the physical and mechanical properties of aluminum casting results printed by using sand mold. Variation is made on the formation of mold sand where there happens a difference of the addition of binding substance rice husk ash and bentonite have been blended into ...
Jurnal Ilmiah Teknik Mesin FEMA; Vol. 1 No. 3 (2013) | 2013
Penanggung Jawab : Harmen, S.T., M.T.Pimpinan Redaksi : A. Yudi Eka Risano, S.T., M.Eng.Ketua Penyunting : : Ahmad Su’udi, S.T., M.T.
Jurnal Ilmiah Teknik Mesin FEMA; Vol. 1 No. 3 (2013) | 2013
Jurnal Fema Vol.1 No.3 terbit pada bulan Juli 2013, terdiri dari 92 halaman, dengan 10 artikel ilmiah.
Jurnal Ilmiah Teknik Mesin FEMA; Vol. 1 No. 3 (2013) | 2013
This study aims to create and analyze the tensile strength of the material matrix composite reinforced polyester resin natural fiber Sansevieria cylindrica leaves that will eventually be in seek of new composite materials which might be expected to be a reference material that is environmentally fri...
Jurnal Ilmiah Teknik Mesin FEMA; Vol. 1 No. 2 (2013): Jurnal FEMA Vo.1 No.2 Tanggal 10 April 2013 | 2013
Producer gas from biomass gasification consists of tar from pyrolysis process which is notdegradation thermal well before out from the reactor. In fact tar is a serious problem that must beconsidered in the process of gasification, especially for an internal combustion engineapplication.Gas cleaning...
Jurnal Ilmiah Teknik Mesin FEMA; Vol. 1 No. 2 (2013): Jurnal FEMA Vo.1 No.2 Tanggal 10 April 2013 | 2013
The background research is the development of science and technology in the field of materials engineering and the demands off indinga new breakthrough in the provision of high quality materials and environmentally friendly. Composite materials of natural fibers that are more light weight, malleable...
Jurnal Ilmiah Teknik Mesin FEMA; Vol. 1 No. 2 (2013): Jurnal FEMA Vo.1 No.2 Tanggal 10 April 2013 | 2013
This paper describe about designing and testing laboratory-scalebiomass energy power plant, toprovideelectricityin remote areasand islandswhich utilizerenewable energyin accordancewith thepresident decreeNo.5/2006. The power plantis built with gasificationreactorwhich designedbased onImbertdowndraft...
Jurnal Ilmiah Teknik Mesin FEMA; Vol. 1 No. 2 (2013): Jurnal FEMA Vo.1 No.2 Tanggal 10 April 2013 | 2013